[Spoon]

Started a new thread. Please follow the link in my signature. Thanks!

[Spoon]

Bumping this with in thread pics, updated prices and lists. Thanks!

[Spoon]

Bump. New items, pics, and prices.

[Spoon]

Bumping. Updated all lists, pictures, and prices.

[Spoon]

Bump. Updated Lists, Pics, & Wants.

[Spoon]

Added items. Updated pics and prices.

[Spoon]

Bump for new items.

[Spoon]

Updated items, pics, & prices.

[SHEMAN]

Could I please ask where I could get my hands on 'WWE Superstars Vince McMahon Kitbash 13'?

I'm in the UK though... I don't even watch WWE but Vince looks just like one of my friends (well... aside from the muscles) and I'd love that figure!

EDIT... That figure must be extremely rare, because I can't find it ANYWHERE online...

[Spoon]

Quote:

Originally Posted by SHEMAN

Could I please ask where I could get my hands on 'WWE Superstars Vince McMahon Kitbash 13'?

I'm in the UK though... I don't even watch WWE but Vince looks just like one of my friends here and I'd love that figure!

EDIT... That figure must be extremely rare, because I can't find it ANYWHERE online...

It's not an official release, just a custom kitbash I made. There's two Lines of WWE figures that use the Origins bodies as a base, Masters of the WWE Universe & WWE Superstars (WalMart exclusive). Some 7 inch WWE and Masterverse figure parts can also be used with Origins. Almost anything on an Origins base body between WWE x2, Origins, Cartoon, & TMNT can be swapped around since they are modular. Recipe below.

Head: 7 inch Mattel WWE Vince McMahon Head. (There's multiple different heads available, I used this BAF head from Stone Cold.) It fit the ball peg perfectly.
Upper Body: WWE Superstars Ric Flair. (Could use any Origins body that matches the skin tone or go with a different color/look entirely.)
Arm Pads: WWE Superstars NWO Hulk Hogan.
Lower Body: WWE Superstars NWO Hulk Hogan. Removed the Hollywood paint on the butt.
Boots: There's a few WWE Superstars that use black, but almost any boots from any Origins Line would work.

[SHEMAN]

Quote:

Originally Posted by Spoon

It's not an official release, just a custom kitbash I made. There's two Lines of WWE figures that use the Origins bodies as a base, Masters of the WWE Universe & WWE Superstars (WalMart exclusive). Some 7 inch WWE and Masterverse figure parts can also be used with Origins. Almost anything on an Origins base body between WWE x2, Origins, Cartoon, & TMNT can be swapped around since they are modular. Recipe below.

Head: 7 inch Mattel WWE Vince McMahon Head. (There's multiple Different heads available, I used this BAF head from Stone Cold.) It fit the ball peg perfectly.
Upper Body: Ric Flair. (Could use any body that matches the skin tone or go with a different color/look entirely.)
Arm Pads: NWO Hulk Hogan.

Lower Body: NWO Hulk Hogan Removed the Hollywood paint on the butt.
Boots: There's a few that use black, but almost any boots from WWE or any Origins Line would work.

Thank you! I'm getting ideas in my head now. I'll watch some videos online and see if the wwe figures I have can be swapped with the masters of the universe figures I have. I have jakks figures I know that much, some basic, some not. I'll see if I can come up with anything!

But that figure you made looks amazing.

[Spoon]

Quote:

Originally Posted by SHEMAN

Thank you! I'm getting ideas in my head now. I'll watch some videos online and see if the wwe figures I have can be swapped with the masters of the universe figures I have. I have jakks figures I know that much, some basic, some not. I'll see if I can come up with anything!

But that figure you made looks amazing.

Thanks and no problem, glad to help! A few quick tips below that may further help. You can also find videos on these for detailed steps & instructions.

If a head opening is too small to fit on a ball peg you can use a rotary tool (Dremel) to widen it. Just do a little at at time so as not to make the opening too big.

If the opening is too big you can do any of the adhesive putty, heat shrink, hot glue, or tapered rubber sink washers tricks. All are reversable. The hot glue trick usually generates the best range of motion results, adhesive putty is pretty much stuck in one place, heat shrink can be tricky but also yield good results. I've never tried the rubber washers trick but it might be even better than hot glue and can be made permanent.

If going the hot glue route be sure to use petroleum jelly on the ball peg before putting the hot glue in the head and sticking them together for forming/molding. If not they'll be stuck together when it dries.

[SHEMAN]

Quote:

Originally Posted by Spoon

Thanks and no problem, glad to help! A few quick tips below that may further help. You can also find videos on these for detailed steps & instructions.

If a head opening is too small to fit on a ball peg you can use a rotary tool (Dremel) to widen it. Just do a little at at time so as not to make the opening too big.

If the opening is too big you can do any of the adhesive putty, heat shrink, hot glue, or tapered rubber sink washers tricks. All are reversable. The hot glue trick usually generates the best range of motion results, adhesive putty is pretty much stuck in one place, heat shrink can be tricky but also yield good results. I've never tried the rubber washers trick but it might be even better than hot glue and can be made permanent.

If going the hot glue route be sure to use petroleum jelly on the ball peg before putting the hot glue in the head and sticking them together for forming/molding. If not they'll be stuck together when it dries.

Thank you for that information.

I always wish at times like this I had someone by my side to teach me.

There are so many things to learn! But this really helps.

Thanks again.