TFW2005HisstankThundercatsTokuNationToyark
Go Back   The Toyark > Toyark Toy Forums >
Reload this Page

Search Results

Rules Register Community Today's Posts Search
Showing results 1 to 15 of 15
Search took 0.00 seconds. Search: Posts Made By: Slicewing09
Forum: Toy and Action Figure General Discussion 12-06-2012, 11:17 AM
Replies: 5
Views: 2,357
Posted By Slicewing09
Yeah, I was gonna go with the rod regardless so I...

Yeah, I was gonna go with the rod regardless so I could have the luxury of removing it if I wanted to. Don't really wanna permanently glue it on there. Thanks for the help though. I'll probably grab...
Forum: Toy and Action Figure General Discussion 12-03-2012, 10:45 PM
Replies: 5
Views: 2,357
Posted By Slicewing09
Sorry for the double post, but I should ask,...

Sorry for the double post, but I should ask, should the rods I order be a bit smaller? I'm sure the tip of his SOCOM was just a tad smaller than the diameter of the suppressor. Don't want the fit to...
Forum: Toy and Action Figure General Discussion 12-03-2012, 10:43 PM
Replies: 5
Views: 2,357
Posted By Slicewing09
Thanks a ton, I'll get to fixing this ASAP. I...

Thanks a ton, I'll get to fixing this ASAP. I should probably order some stands myself. This cannot and will not happen to the Jungle Fatigues Big Boss I'm ordering this weekend.
Forum: Toy and Action Figure General Discussion 12-02-2012, 08:27 PM
Replies: 5
Views: 2,357
Posted By Slicewing09
More problems with PAK Solid Snake

Same guy who had elbow pad issues before. Snake recently tipped over on his shelf, and off snapped the end of his SOCOM inside of the suppressor. I was absolutely distraught to say the least, but I'm...
Forum: Tech Support 10-16-2012, 04:52 PM
Replies: 1
Views: 3,677
Posted By Slicewing09
Avatars not working?

Each time I try and select an avatar, whether it falls under the size regulations or not, I select "save changes", and I'm then prompted with "file upload failed." What exactly's going on here? This...
Forum: Toy and Action Figure General Discussion 10-14-2012, 11:43 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
I actually went ahead and tried just dabbing it...

I actually went ahead and tried just dabbing it in glue and shoving it in there. Didn't work at all, but his joints are fine, so at least I didn't screw up. I'll work up the courage to try the arm...
Forum: Toy and Action Figure General Discussion 10-14-2012, 11:41 PM
Replies: 52
Views: 8,385
Posted By Slicewing09
The fact that my old 12 inch Major Chip Hazard is...

The fact that my old 12 inch Major Chip Hazard is chilling 4 feet from my bed makes me want to disregard my hero/villain ratio and just go ahead and call it quits.
Forum: Toy and Action Figure General Discussion 10-11-2012, 10:44 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
Okay. Got that part down for sure. Back to...

Okay. Got that part down for sure.

Back to fixing his elbow pads though...I can't help but think that sounds perilous as can be. If I were to just dab the C-shaped piece of the elbow pad (the...
Forum: Toy and Action Figure General Discussion 10-11-2012, 08:18 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
I will do just that. Before I turn the hair dryer...

I will do just that. Before I turn the hair dryer loose on this guy though, would a dunk in hot water be a reasonable alternative, or is one considerably more effective than the other?
Forum: Toy and Action Figure General Discussion 10-10-2012, 11:03 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
Sounds good. Thanks for putting up with this...

Sounds good. Thanks for putting up with this question bombardment. I'll at LEAST throw some Krazy Glue on there tomorrow and plug it back in that way. Unsure if I'm mentally ready to tackle the elbow...
Forum: Toy and Action Figure General Discussion 10-10-2012, 10:12 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
Alright, thanks a lot. I'll give it a try...

Alright, thanks a lot. I'll give it a try tomorrow. Is there even a remote chance that the socket will warp and be unable to support the arm at all?
Forum: Toy and Action Figure General Discussion 10-10-2012, 09:20 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
I could definitely try that. Just with the floor...

I could definitely try that. Just with the floor finish, it pops back in pretty decently and stays put, but after a few days of posing, it begins to work its way back out. Bout how long should I blow...
Forum: Toy and Action Figure General Discussion 10-10-2012, 09:10 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
Thank you VERY much. I will definitely give this...

Thank you VERY much. I will definitely give this a try once I work up some courage (I really, really don't want to break this guy more than he is already), or I may find someone else to do it for me...
Forum: Toy and Action Figure General Discussion 10-10-2012, 09:34 AM
Replies: 18
Views: 3,159
Posted By Slicewing09
I actually think you're right about the pivot...

I actually think you're right about the pivot joint, I just wasn't sure how to word that. How exactly would I go about getting that back in there? Just dab the ends in glue and stick it back or what?...
Forum: Toy and Action Figure General Discussion 10-09-2012, 11:08 PM
Replies: 18
Views: 3,159
Posted By Slicewing09
Play Arts Kai Metal Gear Solid figures

I need some help, guys. I love MGS, and I recently purchased a PAK Solid Snake and proceeded to fall in love. This figure is awesome! All was well until just a few weeks ago, I was just casually...
Showing results 1 to 15 of 15

 
Forum Jump
The Chosen Prime

All times are GMT -7. The time now is 05:07 AM.

Powered by vBadvanced CMPS. Powered by vBulletin. Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.